How to Perform the Zercher Squat for Strength Training

Introduction

In many cases, a lifter’s leverages, injury history, or both, can frustrate his ability to perform well in large compound movements. Sadly, it’s left many with no choice but to abandon these moves and any variations for redundant sets of isolation training on machines, or movements that don’t provide as much bang for their buck from a strength training perspective. Squats are one of the biggest victims of this problem, and the Zercher squat separates itself from the rest.

The Problem with Barbell Squats

Barbell back squats can be hard on lifters’ backs if they have a history of injury—or, in some cases, if they have long legs. On a similar note, barbell front squats ask a whole lot of a lifter’s mobility if they want to attempt a clean grip and use full range of motion. A California-style setup can be quite uncomfortable on the deltoids.

The Solution: Zercher Squat

To solve all of this, the Zercher squat may be the hidden gem you’ve been missing in your training. Because of the bar’s placement, it allows for a lifter to squat deep while minimizing shear on the lower back. In addition, it doubles as a great core exercise.

- Advertisement -

How to Perform the Zercher Squat

To perform the Zercher squat, follow these steps:

1. Set a bar in the squat rack at waist level: Don’t be over the top with the amount of weight you decide to load. In fact, it’s probably a safe decision to start with very light weight to get the feel for the lift and its comfort level. Next, slide the crooks of your arms (elbow joint) under the bar, and interlace your fingers. Your knuckles should be facing the ceiling, and the bar should be right in the bend of your elbows. The width of your elbows should be no more than your hip width.
2. Stand tall, and assume your desired squat stance: If you generally squat with a very narrow stance, it would be helpful to widen out your foot width a little bit, so that the body creates enough space for clearance and to accommodate the new load placement. Remember to keep the fists facing up.
3. Next, keeping your torso as upright as possible, descend slowly: Your intention, like any barbell movement, should be for the barbell to travel in a straight line up and down. In other words, don’t allow it to drift forward as you descend. That will place stress on the lower back and weaken the lift. You’ll keep a linear path by keeping the hands up.
4. Spread the knees and dig in: Since your elbows will be facing down, be sure to spread the knees to allow you to reach the depth that you’re capable of, while not being “blocked” by your thighs. Dig in with the heels, and ascend strongly, aiming for the back of your head to go through the roof.

Zercher Squat Tips and Tricks

There’s no doubt this isn’t a comfortable exercise. But it sure is effective. You should feel a significant amount of added tension in the glutes and hamstrings, due to the placement of the load (more proximal to the hip joint). To get the most out of this movement, take these cues to heart:

Wear a hoody or long sleeve shirt, and dress the bar with fat grips

Doing this will dull the amount of pressure you feel in your elbows, which will come in quite handy when the weight starts getting heavy. The fat grips will increase the amount of surface area the bar “cuts into” on your arms, and make carrying it much more comfortable.

Wear flat shoes—not Olympic lifting shoes

I’ve found that Olympic lifting shoes, complete with their heel wedge, can cause a lifter to drift too far forward during this lift. Since the elbows are down, it’s harder to correct this propensity when it happens. To remain more vertical, in this case it’s a good idea to stick with flats.

Keep a low rep range

You’re going heavy with a front load, and that’s already the general cue with other front loaded exercises like front squats or front split squats. You can only handle that load in your arms for so long before your upper body begins to fatigue (usually before your lower). With that said, limit your sets to 6 reps or fewer, and if you’re chasing a pump, simply do more sets with slightly shorter breaks in between.

It’s just one more tool

Remember that we have many resources at our disposal to train around injuries or to train friendly to unfavorable leverages. The Zercher squat doesn’t have to be a new everyday lift, but it can enter the rotation of effective alternatives to get the most out of your strength workouts with the least collateral damage. Your body will thank you.

Conclusion

In conclusion, the Zercher squat is a powerful exercise that can be an effective addition to your strength training routine. By following the proper form and incorporating the tips and tricks outlined above, you can minimize discomfort and maximize the benefits of this exercise.

FAQs

Q: What is the Zercher squat?

A: The Zercher squat is a type of squat that involves holding a barbell with your arms wrapped around it, with your elbows facing down.

Q: What are the benefits of the Zercher squat?

A: The Zercher squat allows for deep squats while minimizing shear on the lower back, and doubles as a great core exercise.

Q: What are some common mistakes to avoid when performing the Zercher squat?

A: Common mistakes to avoid include allowing the barbell to drift forward during descent, not spreading the knees enough, and not keeping the torso upright.

Q: Can I use the Zercher squat if I have a history of back injuries?

A: Yes, the Zercher squat can be a great option for individuals with a history of back injuries, as it allows for deep squats while minimizing shear on the lower back.